View Profile: bluesjumper - Halloween Forum
Hello there, is this your first visit?
  • bluesjumper's Avatar
    05-17-2019, 07:30 PM
    I found this chest in neighbor's trash this morning, and I was wondering if my creature dude could be made to slowly come out of the chest as the lid opens? Creature is made of heavy foam and latex, and I'd have to shave a couple inches off the rear for him to fully fit. Even then, his head wouldn't fully clear the lid. The lid would remain open about 45 degrees, which I'd be fine's like he's peeking outside his box and then gradually comes out to greet his guests/victims. I only...
    3 replies | 98 view(s)
  • bluesjumper's Avatar
    05-10-2019, 06:42 AM
    J-Man, you are my hero! I applied your initial ideas and it didn't take much experimenting to get the motion I wanted. And the lateral head movement started to work as well. Here is how it looks now: Thanks again!!
    15 replies | 367 view(s)
  • bluesjumper's Avatar
    05-09-2019, 05:43 AM
    I could really use some advice to save me time and aggravation. See my video first: I'm having a couple challenges with the head. First, what should I do to get the head to come up more vertical? At its highest point, it is still too angled down for my taste. My short metal piece is around 5.75" and longer one is 8". Second, the reason why the head is positioned directly on the spine (instead of on a 90 degree elbow) is because I'm trying to also introduce a...
    15 replies | 367 view(s)
  • bluesjumper's Avatar
    04-27-2019, 04:46 PM
    bluesjumper started a thread Prop Showcase: Pumpkin Sentinel in Halloween Props
    Here is my best attempt to match Pumpkinrot's pumpkin sentinel:
    1 replies | 213 view(s)
  • bluesjumper's Avatar
    04-25-2019, 05:52 AM
    I'm about to start building cauldron creep prop and have purchased this barrel to serve as the cauldron. The barrel is pretty cool as-is but I may glue a few skulls or bones to it. You have any other ideas? But primarily, check out the little shelf that rotates and holds up the smaller barrel. I'm thinking I should leave it, and the lid, intact as part of the prop? Perhaps I fill the small barrel with...
    1 replies | 173 view(s)
  • bluesjumper's Avatar
    04-24-2019, 12:18 PM
    If you've worked with corpsing barber shop heads and have some photos, I'd love to see them. I have several heads I'd like to work on for my first time. Here are a few ideas I had found:
    0 replies | 175 view(s)
No More Results
About bluesjumper

Basic Information

About bluesjumper
Boston suburb


Total Posts
Total Posts
Posts Per Day
General Information
Last Activity
05-17-2019 07:30 PM
Join Date
Activity Information
  • Total Points:
  • 154
  • Activity Level:
  • 4
  • To Next Level:
  • 27
  • Percent Into Level:
  • 55.74% Achieved
  • Daily Activity:
  • 0 / 3.86 (0%)
  • Weekly Activity:
  • 0.2 / 27 (0.74%)
  • Monthly Activity:
  • 18.1 / 119.57 (15.14%)
  • Points for Attachment:
  • 12
  • Points For Thanks Given:
  • 1
  • Points For Thanks Received:
  • 2
  • Points For Likes Given:
  • 0
  • Points For Likes Received:
  • 7
  • Points For Dislikes Given:
  • 0
  • Points For Dislikes Received:
  • 0
  • :
  • 0
  • :
  • 0