styrofoam cutter

**TheGothicPrincess** · 07-23-2009,07:04 AM

I am trying to locate a hot wire styrofoam cutter. If you know where I can purchase a hand held unit, please let me know.

**Rikki** · 07-23-2009,07:11 AM

I know that Michael's and JoAnn's both carry hand held styrofoam cutters. I bought two different styles at Michael's last year - a battery powered hot wire set up and an electric one that has a thin metal rod with nothing attached at the other end.

**Johnson724** · 07-23-2009,07:29 AM

I got the one from Michaels. It has a cord attached to it and a thin rod. They have another one which is cheeper that almost looks like a jig saw with a wire for the blade. You have to be carefull and not go too fast or the wire will break. I think it has a replacement wire with it. The one I have you can go a little faster but the rod will start to bend if you go to fast. It will also begin to cool off as your cutting but you can use a sawing motion to get to a hotter part of the rod. It does leave marks if you do it that way but I was able to sand mine down.

**shadowopal** · 07-23-2009,08:28 AM

If you want bigger cutters, you can buy from Hot Wire Foam Factory ( Hotwire*Foam*Factory ) or make your own. There is a how to on Garage of Evil Somewhere.

**TheGothicPrincess** · 07-23-2009,10:58 AM

thanks guys, I don't have a micheal's close, but I will make a point to stop at the nearest one on one of our trips.

**TK421** · 07-23-2009,11:33 AM

For the record, I have also bought the battery-powered "hot-wire" styro cutter and the plug-in styro cutter wand from Michaels.

The battery-powered one is a great idea, but it runs through D sided batteries very quickly (you're lucky to get through one tombstone-sized project). The plug-in wand is nice, and does a great job on the pill styrofoam, but It's pretty slow going when it comes to cutting clean through an inch or more of styrofoam. The wand is great for detail work, and the fact that you don't have to worry about batteries is a HUGE plus.

If you're going to be doing a lot of styrofoam cutting, I would suggest you check onling for a more professional hot-wire styrofoam cutter. Even better, and a lot cheaper, follow the garage-of-evil's plans for their $20 variable power hot-wire styro cutter.

Hot-Wire Foam Pro Tools For Cheap!

**TNBrad** · 07-23-2009,04:33 PM

There is a table top battier/plug one at Hobby Lobby and there is a 40% off coupon on the net.
Weekly Specials : Hobby Lobby

**TK421** · 07-23-2009,06:55 PM

Most of the time I just use a box cutter to sculpt my styrofoam, but I've been trying to do some research on good styrofoam hot-wire cutters.

The two that I have currently are very cheap and not very reliable. One is a $5 cutter that requires two "D" batteries to heat the wire. It's not bad for short bursts through thin sheets, but it runs through batteries pretty quick. The other is a cheap Michaels find hot-wire "wand" cutter. It worked pretty good -- until it broke the same afternoon I bought it!

I think the main problem with both of these cutters is they don't get hot enough.

I have found a cutter on eBay for $30 that claims to run at a cutting temperature of 428° F. I know this may be a stupid question, but is that a good temp for styrofoam cutting?

I know my wood burning iron runs at about 750° F and that's probably too hot for finer wire cutting.

**Haunty** · 07-23-2009,07:28 PM

Disclaimer- I don't work for or was paid for these comments.

I just recently purchased the Hotwire Foam factory kit (pro kit 4 tools, dvd, adjustable power supply) at Hauntcon in April. Do also own the Micheals craft foam cutting tool, & the scroll foam cutter from Hobby Lobby.

The Hotwire system can be purchased either online or any conventions they attend.

When I compared the Michaels wand foam cutter vs the similar HWFF wand, the Hot wire wand heated up quicker & cut through foam quicker too. Didn't like the design of the Michaels wand plug to the power supply. It's not permanently attached to it, & came unplugged a few times.

Hotwire*Foam*Factory